Name: Leatt 7.5 ADV HydraDri Glove - Stealth
Brand: Leatt
SKU: LE6024040560
Price: 191.95 AUD
Availability: InStock

The Leatt ADV HydraDri 7.5 is a waterproof adventure glove built for riders who keep going when the weather turns. A HydraDri EVO membrane sits behind the outer shell to block rain while still letting moisture escape, and a seamless leather palm keeps the grip clean and consistent on long days in the saddle.

Protection comes from 3DF soft impact foam at the knuckle, CE tested and certified to EN 13594:2015 Level 1, backed by TPR on the fingers, palm sliders and dual-layer material through the areas most likely to take a hit. This is the standard, above-the-wrist length with a Velcro cuff closure and the FreeFlex strap for wrist movement.

Suited to adventure and touring riders in Stealth colourway, with a rain wiper on the left thumb and reflective detailing for low light.

HydraDri EVO waterproof/breathable membrane rated 20,000mm / 20,000g/m²
3DF soft impact foam knuckle, CE tested and certified to EN 13594:2015 Level 1
Seamless leather palm for consistent grip and reduced bunching
TPR protection across the fingers with palm sliders
Dual-layer material in critical impact areas
Stretch Micro Leatt RipStop chassis
Multi-row technical thread stitching for durability
Standard above-the-wrist length with Velcro cuff closure
Velcro FreeFlex strap fastening for wrist range of motion
Pull loop at the cuff for easy entry
Rain/screen wiper on the left thumb
Reflective detailing
Plastic-free packaging

Pair of gloves

Brand	Leatt
Model	ADV HydraDri 7.5 Glove
Type	Adventure/touring motorcycle glove, standard above-the-wrist length
Colourway	Stealth
SKU	LE6024040564
Waterproofing	HydraDri EVO membrane, 20,000mm waterproof / 20,000g/m² breathable
Certification	CE tested and certified impact protection — knuckle, EN 13594:2015 Level 1
Protection	3DF soft impact foam knuckle; TPR on fingers; palm sliders; dual-layer material in critical impact areas
Palm material	Seamless leather
Shell material	Stretch Micro Leatt RipStop
Construction	Multi-row technical thread stitching
Closure	Velcro cuff closure with Velcro FreeFlex strap fastening; pull loop at cuff
Extra features	Rain/screen wiper on left thumb; reflective detailing
Sizes	Manufacturer copy states S–2XL; our stocked range runs S–3XL — check the size selector for current availability
Packaging	Plastic-free

Refer to the Leatt size guide and measure your hand before ordering — a snug fit keeps the knuckle protector seated over the joint.
Use the cuff pull loop when putting the gloves on, then set the Velcro cuff and FreeFlex strap so the glove is secure without restricting wrist movement.
Brush dirt and grit off the Velcro closures regularly; trapped debris stops the fastening from holding properly.
Clean by hand in cool water with a mild soap, then rinse — avoid solvents, petrol, bleach and harsh detergents, which will damage the leather palm and the HydraDri EVO membrane.
Air dry at room temperature away from direct sunlight, exhaust pipes, heaters and tumble dryers; forced heat hardens leather and can delaminate the membrane.
Make sure the gloves are fully dry inside before storing, and keep them flat or lightly stuffed in a cool, dry place so the shape and protectors are not deformed.
Expect a short break-in period as the leather palm softens and moulds to your hand.
Inspect the knuckle protector, finger TPR and palm sliders periodically; replace the gloves after a crash or any significant impact, as the protection is not designed to be reused.
Check stitching and seams before long trips and repair small failures early rather than letting them run.