LS2 FF811 Vector II Carbon Savage Helmet - White / Red / Grey 06

Sport helmet with a modern design to enjoy both on city roads and highways. Its carbon fibre provides extraordinary lightness and resistance. Excellent dynamic flow-through ventilation. Wide anti-scratch visor prepared for the anti-fog system, Pinlock Max Vision, and drop-down sun visor for greater safety.

SPECIFICATIONS

• Material: Carbon
• Weight: 1300 (±50 gr.)
• Sizes (6 Shells): 2XS-XS/S/M/L/XL/2XL- 3XL-4XL
• Shape: Long Oval
• ECE 22.06 Homologation

SAFETY

• Emergency Release System
• Micrometric Metal Buckle
• Multi-Density EPS
• Reinforced Chin Strap

VENTILATION

• Chin and top vent
• Exhaust vents
• Channelled EPS
• Breath Deflector

COMFORT

• X- Static© Silver Liner Fabric
• Ready for LS2 INTERCOM (Bluetooth by Cardo)
• Removable and washable
• Breathable
• Hypoallergenic
• Laser-cut foam

VISOR

• Pinlock® 120 MaxVision™ included
• Wide Visor
• Twin Visor System
• Scratch-resistant
• UV-resistant
• Quick Release System

INTERCOM COMPATIBILITY

• Compatible with the LS2 Spectrum intercom.

• Carbon fibre shell for low weight and high impact resistance
• ECE 22.06 homologated
• Approximately 1300 g (±50 g) shell weight
• Six shell sizes across the 2XS-4XL range
• Long oval internal shape
• Pinlock 120 MaxVision anti-fog insert included
• Wide visor with scratch-resistant and UV-resistant treatment
• Twin visor system with drop-down sun visor
• Quick-release visor changing system
• Dynamic flow-through ventilation with chin and top vents plus rear exhaust vents
• Channelled EPS for airflow through the shell
• Multi-density EPS liner
• Emergency Release System for cheek pad removal by first responders
• Micrometric metal ratchet buckle with reinforced chin strap
• Removable, washable X-Static silver liner fabric, breathable and hypoallergenic
• Laser-cut comfort foam
• Breath deflector fitted
• Shaped for the LS2 intercom system (Bluetooth by Cardo), compatible with the LS2 Spectrum intercom

• LS2 FF811 Vector II Carbon helmet
• Pinlock 120 MaxVision insert

Measure the widest part of your head just above the ears and check it against our six-shell sizing guide; the FF811 is a long oval shape, so riders with a rounder head shape may find pressure at the forehead and rear.
Remove the cheek pads and comfort liner for washing — hand wash in cool water with a mild detergent, rinse thoroughly, and air dry away from direct heat and sunlight before refitting.
Clean the shell and visor with warm water and a mild soap using a soft microfibre cloth. Avoid petrol, solvents, alcohol-based cleaners and abrasive pads, which damage the paint, the scratch-resistant visor coating and the Pinlock insert.
Soften stubborn insects by laying a damp cloth over the visor for a few minutes rather than scrubbing.
Handle the Pinlock 120 MaxVision insert by the edges only; the anti-fog side is soft and marks easily. Remove it before cleaning the inside of the visor.
Use the quick-release system to remove the visor for cleaning or replacement, and check the visor seats and latches correctly before riding.
Open the chin, top and exhaust vents in warm weather and close them in cold or wet conditions; check the vent sliders move freely and are clear of grit.
Fit the intercom into the helmet's dedicated speaker recesses and cable channels so the liner sits flat and the fit is not compromised.
Check the micrometric buckle engages fully every ride and keep the ratchet strap clean; never ride with the strap loose or unfastened.
Store the helmet in its bag in a cool, dry place, out of direct sunlight and away from fuel, exhaust fumes and solvents. Do not hang it on a mirror or handlebar, and never rest it on the tank.
Replace the helmet after any impact, even if there is no visible damage — the EPS liner compresses once and will not protect you a second time.
Do not paint, apply stickers or adhesives, or drill the shell, as this can weaken the carbon and voids ECE approval.