K8 3.0 Knee Brace (LT) | Carbon/Graphite 2X-Large Left

The POD K8 3.0 is the brand's flagship knee brace, built around a forged carbon composite frame and POD's industry-first adaptive lower frame. This listing is for a single left brace in the Carbon/Graphite colourway, size 2X-Large.

It is aimed at motocross, enduro and off-road riders — and action-sports athletes generally — who want ligament support and impact protection without the bulk of a traditional metal brace. The Human Motion Hinge uses synthetic ligaments for progressive, multi-directional motion control rather than an abrupt mechanical lock-out, and the full-coverage re((SPONSE)) impact system is certified to CE Level 2 (EN 1621-2).

Developed over five years as a complete redesign of the K8 2.0, the 3.0 adds adaptive cuffs, a bonded Hex Grip liner and the Quick-Loc clip system so the brace anchors to the leg quickly and stays put through a moto. Braces are sold individually — order a right-hand brace separately if you need a pair.

• Forged Carbon Composite frame made from pressed, heated and moulded layers of military-grade carbon fibre
• CE Level 2 (EN 1621-2) certified full-coverage re((SPONSE)) viscoelastic impact system
• Live Adaptive Lower Frame with two rigid composite struts down each side of the tibia
• Flexible TPU bridge lets the lower frame conform to different leg shapes
• POD states the adaptive lower frame reduces the risk and severity of rotational forces by 54%
• Human Motion Hinge with pre-curved Synthetic Ligaments for progressive multi-directional control
• Increased range of flexion from 118° to 134°
• Symmetrical hinge design and moulded knee gripper for a secure fit
• Clip-in hinge pad and thicker hinge walls for added durability
• Two progressive extension controls included — 10°–20° (mid grey) and 20°–30° (dark grey)
• Adaptive cuffs conform to leg size and shape and accommodate muscle movement
• Bonded Hex Grip liner with embossed air channels for temperature management and reduced odour
• Liner is weather and chemical resistant, splash resistant to oils and fuels, with zero water absorption
• Quick-Loc clip system with low-profile interior straps for faster fitting
• Soft Touch strap ends, straps adjustable from both ends, and a no-swing D-loop on strap #1

• One K8 3.0 left knee brace
• Two extension controls (10°–20° and 20°–30°)

Fit the brace with the hinge centred over the side of the knee joint, then do the straps up in the numbered order marked on the straps — strap #1 first.
Adjust the straps from either end and use the Quick-Loc clips to set a firm but not restrictive tension; re-check tension after the first few minutes of riding.
Swap between the 10°–20° and 20°–30° extension controls to suit how much extension damping you want; only fit one set at a time and make sure both sides match.
Rinse mud, dust and grit off after riding — especially around the hinge and lower frame — as trapped grit accelerates hinge wear.
Hand wash the liner and straps in warm water with a mild soap, rinse thoroughly and air dry away from direct heat. Do not machine wash, tumble dry or dry on a heater.
Wipe the carbon frame with a damp cloth only. Avoid petrol, solvents and harsh detergents on the frame and hardware.
Periodically check the hinge fasteners, strap clips and cuffs for wear or looseness, and replace worn straps, pads and clips with genuine POD spare parts.
Store the brace flat and dry, out of direct sunlight, and don't leave it in a hot vehicle or enclosed trailer.
Do not drill, cut, heat or otherwise modify the carbon frame. Inspect the brace after any heavy crash and replace it if the frame, hinge or impact padding is cracked or deformed.
A knee brace is protective equipment, not a substitute for medical advice — if you are rehabilitating an injury, have the fit checked by your physiotherapist or specialist.